# LCR GSM options
#################
-# Enable debugging of OpenBSC library.
-# Refer to OpenBSC project for debugging options.
-# By default, debugging is turned off.
-#debug DRLL:DCC:DMM:DRR:DRSL:DNM:DSMS:DMNCC:DMNSMS:DPAG:DMUX:DMEAS
-
# Two Loopback interfaces for audio transfer between OpenBSC and mISDN.
+# They are also used for any Osmocom-BB interface, if exists.
# The first interface must provide B-channelis for each call mobile call.
# The seond interface links them to LCR.
-# Use 30 B-channels unless you need more due to many TRXs.
+# Use 30 B-channels unless you need more due to many TRXs or mobile stations.
# -> Load with: "modprobe mISDN_l1loop pri=1 nchannel=30"
# By default "mISDN_l1loop.1" and "mISDN_l1loop.2" is used.
#interface-bsc mISDN_l1loop.1
#interface-lcr mISDN_l1loop.2
-# GSM network names.
-# This name is presented to the mobile station.
-# By default 'LCR' is used.
-#long-name Linux-Call-Router
-#short-name LCR
-
-# Give the GSM country code.
-# The country code is different from the PSTN country code. E.g Germany uses
-# 262 instead of 49. Use this for IMSI catching.
-# This will override the default value of 1 = 'test country';
-#mcc 001
-
-# Give the GSM network code.
-# The network code is different from the PSTN network codes. Change this if
-# you run different test networks in the same locations.
-# This will override the default value of 1 = 'test network';
-#mnc 01
+# Enable debugging of OpenBSC library.
+# Refer to OpenBSC project for debugging options.
+# By default, debugging is turned off.
+#debug DRLL:DCC:DMM:DRR:DRSL:DNM:DSMS:DMNCC:DMNSMS:DPAG:DMUX:DMEAS
-# Give the location area code.
-# The location area code is not known to the author of LCR. Don't change it!
-#lac 1
+# Give openbsc.cnf config file
+# It will be located at /usr/local/lcr by default.
+#config openbsc.cfg
# Give database of Home Location Register (HLR)
# HLR stores all subscribers. It will be used to grant access to the network.
# The database is located at /usr/local/lcr by default.
#hlr hlr.sqlite3
-# Authorization of unknown subscribers.
-# To allow all subscribers to access the network, use this option.
-# By default, subscribers are only accepted if allowed in the HLR
-allow-all
-
# To keep layer 2 connection to BS11 when quitting, use this option.
# It is only usefull for developing. TRX will stay on.
# Also changes in frequency, mcc, mnc, lac while keeping layer 2 will cause
# Warning: Keeping layer 2 link may prevent emergency calls. (See below)
#keep-l2
-# You must define a list of your BTS'.
-# Usage: 'bts bs11 <card> <frequency> [<frequency 2>]
-# The keyword 'bts' is used to specify a BTS. Multiple BTS' may be defined.
-# The 'bs11' keyword specifies a BS11 BTS connected to an E1 card.
-# The frequency is given for the first TRX (tranceiver).
-# In case of a second tranceiver, give frequency 2.
-bts bs11 0 123
-
-# Shutdown on emergency calls:
-# This option will prevent a shutdown if an emergency call is received. In
-# case of an emergency, a mobile phone may log onto you GSM network and may
-# use it to set up an emergency call.
-# The received emergency call will have 'emergency' as dialed number. But this
-# number can't be dialed on PSTN networks without chaning.
-# If you disable shutdown, be sure to provide routing of emergency calls to
-# emergency facility. If you can't do that, don't touch it!
-#no-emergency-shutdown
-
# Write BTS-Link traffic to PCAP file.
#pcapfile pcap