Make LCR run with OpenBSC main branch.

[lcr.git] / default / gsm.conf

diff --git a/default/gsm.conf b/default/gsm.conf
index a0f4b49..d0a9c6f 100644 (file)
--- a/default/gsm.conf
+++ b/default/gsm.conf
@@ -4,7 +4,7 @@
 # Enable debugging of OpenBSC library.
 # Refer to OpenBSC project for debugging options.
 # By default, debugging is turned off.
-#debug DRLL:DCC:DMM:DRR:DRSL:DNM:DSMS:DMNCC:DMNSMS:DPAG:DMUX
+#debug DRLL:DCC:DMM:DRR:DRSL:DNM:DSMS:DMNCC:DMNSMS:DPAG:DMUX:DMEAS
 
 # Two Loopback interfaces for audio transfer between OpenBSC and mISDN.
 # The first interface must provide B-channelis for each call mobile call.
@@ -15,27 +15,9 @@
 #interface-bsc mISDN_l1loop.1
 #interface-lcr mISDN_l1loop.2
 
-# GSM network names.
-# This name is presented to the mobile station.
-# By default 'LCR' is used.
-#long-name Linux-Call-Router
-#short-name LCR
-
-# Give the GSM country code.
-# The country code is different from the PSTN country code. E.g Germany uses
-# 262 instead of 49. Use this for IMSI catching.
-# This will override the default value of 1 = 'test country';
-#mcc 001
-
-# Give the GSM network code.
-# The network code is different from the PSTN network codes. Change this if
-# you run different test networks in the same locations.
-# This will override the default value of 1 = 'test network';
-#mnc 01
-
-# Give the location area code.
-# The location area code is not known to the author of LCR. Don't change it!
-#lac 1
+# Give openbsc.cnf config file
+# It will be located at /usr/local/lcr by default.
+#config openbsc.cfg
 
 # Give database of Home Location Register (HLR)
 # HLR stores all subscribers. It will be used to grant access to the network.
@@ -43,11 +25,6 @@
 # The database is located at /usr/local/lcr by default.
 #hlr hlr.sqlite3
 
-# Authorization of unknown subscribers.
-# To allow all subscribers to access the network, use this option.
-# By default, subscribers are only accepted if allowed in the HLR
-allow-all
-
 # To keep layer 2 connection to BS11 when quitting, use this option.
 # It is only usefull for developing. TRX will stay on.
 # Also changes in frequency, mcc, mnc, lac while keeping layer 2 will cause
@@ -55,14 +32,6 @@ allow-all
 # Warning: Keeping layer 2 link may prevent emergency calls. (See below)
 #keep-l2
 
-# You must define a list of your BTS'.
-# Usage: 'bts bs11 <card> <frequency> [<frequency 2>]
-#  The keyword 'bts' is used to specify a BTS. Multiple BTS' may be defined.
-#  The 'bs11' keyword specifies a BS11 BTS connected to an E1 card.
-#  The frequency is given for the first TRX (tranceiver).
-#  In case of a second tranceiver, give frequency 2.
-bts bs11 0 123
-
 # Shutdown on emergency calls:
 # This option will prevent a shutdown if an emergency call is received. In
 # case of an emergency, a mobile phone may log onto you GSM network and may